How to Import an IFC File into Revit

Nine steps in Revit, or one sentence in Mira.

Do it with Mira

From the guide: The Best Revit AI Plugins of 2026

Quick answer

Link it with Insert tab › Link panel › Link IFC. The link stays read-only and updates when you reload it, and Autodesk calls linking the preferred method. To turn the IFC into a new Revit model instead, use File tab › Open › IFC.

Or, just ask Mira, a free add-in, to move a category to another workset once the model lands.

The manual way

How to do it in Revit

  1. Step 1: Decide whether to link or open

    Link the IFC when you need another team's model as a reference while you keep designing in Revit. You can't edit a linked IFC, and reloading it brings in changes to the file. Autodesk calls this the preferred and fully supported route (Autodesk Help: Using IFC Files).

    Open the IFC when you want a new Revit model that starts from its data. Revit tries to convert IFC elements into native families, categories and parameters. Autodesk warns that current IFC standards can't support a complete 1:1 translation, and later changes to the IFC don't carry over.

    Check the schema before you start. The Revit 2027 Help lists IFC2x3, IFC4 and IFC4.3 for linking (Autodesk Help: About Revit and IFC). The 2025 and 2026 Help lists IFC2x3, IFC2x2 and IFC2x for opening or linking, and IFC4 for linking only (Autodesk Help: About Revit and IFC, 2026).

  2. Step 2: Set the template and class mapping

    Before you link or open, click File tab › Open › IFC Options. In the Import IFC Options dialog, click Browse to pick a template. Without one, Revit uses the first template listed under File Locations in the Options dialog (Autodesk Help: Select a Template for IFC Files).

    In the same dialog, click Load to load a class mapping file, which maps IFC classes to Revit categories and subcategories (Autodesk Help: Load an IFC Class Mapping File). Or double-click a category to override it, click Standard to reset, and click Save As to keep your mapping as a file (Autodesk Help: Override Categories for IFC Objects).

    The template also sets the phase. Linked IFC elements take their Phase Created from the starting view of the template used for the link (Autodesk Help: About Linking to IFC Files). If the link shows up in the wrong phase, see how to use phases in Revit.

  3. Step 3: Make the right workset active

    In a workshared model, new elements go on the active workset. Pick it from the Active Workset drop-down on Collaborate tab › Manage Collaboration panel, or from the status bar (Autodesk Help: Edit a Workset).

    For IFC links, Autodesk Support says to activate the target workset first (Autodesk Support: IFC link not displayed after closing Workset to which it was not assigned in Revit). If the model isn't split up yet, start with how to set up worksets.

  4. Step 4: Link the IFC file

    Open the host model and click Insert tab › Link panel › Link IFC. In the Open IFC File dialog, browse to the IFC file and select it (Autodesk Help: Link an IFC File).

    In Revit 2025, the Help steps go straight to Open. In Revit 2026 and 2027, set the positioning first.

  5. Step 5: Choose a positioning option, then click Open

    Revit 2026 added a positioning drop-down to the IFC link dialog. The default places the link's origin at Revit's internal origin (Autodesk Help: IFC Link Enhancements).

    The 2026 Help says to choose Auto - Origin to Origin in most cases, and Auto - By Shared Coordinates when the host model uses shared coordinates. The 2027 Help lists Auto - IFC Origin to Internal Origin for most cases and IFC Origin to Survey Point for shared coordinates (Autodesk Help: Link an IFC File, 2027). Then click Open.

    Don't use origin-to-origin placement when the geometry sits more than 20 miles (32 km) from its origin (Autodesk Help: Positioning for Imports and Links).

  6. Step 6: Leave the .ifc.RVT file alone

    When you link, Revit writes three files from the IFC. The first is an intermediate Revit model, such as Arch.ifc.RVT for Arch.ifc. The others are a log ending .ifc.log.html and a shared parameters file ending .ifc.sharedparameters.txt. Revit then links the intermediate model into yours (Autodesk Help: Link an IFC File).

    Don't open or edit the .ifc.RVT. Autodesk warns that changing it can stop your model from picking up later changes to the IFC (Autodesk Help: About Linking to IFC Files).

  7. Step 7: Work against the link

    A linked IFC is read-only, but you can dimension to its faces, snap and align to it, and tag its elements. You can host some face-based families, such as conduit and some electrical devices. You can't put a door or window in a linked IFC wall (Autodesk Help: Using IFC Files).

    Room Bounding is off by default for a linked IFC. To place rooms against its walls, select the link, click Type Properties in the Properties palette, and select Room Bounding (Autodesk Help: Use Room Boundaries in a Linked Model). IFC curtain elements can't bound rooms, so draw room separation lines along them.

  8. Step 8: Reload when the IFC changes

    Revit updates links when you reopen the project. To update without closing, click Manage tab › Manage Project panel › Manage Links, select the IFC link, and click Reload (Autodesk Help: Unload and Reload Linked Models).

    On reload, Revit checks the IFC's timestamp and size. If either changed, it matches elements by their IFC GUIDs, then adds, updates and deletes elements to match the file (Autodesk Help: About Linking to IFC Files). Recheck dimensions and alignments afterward, because geometry changes can break them.

  9. Step 9: Or open the IFC as a new model

    Click File tab › Open › IFC and select the file. Under Files of type, you can pick ifc, ifcXML or ifcZIP (Autodesk Help: Open an IFC File).

    The dialog has two options, both on by default. Auto-Join Elements joins walls to walls and columns; clearing it can speed up the import. Correct lines that are slightly off axis fixes lines less than 0.1 degree off; Autodesk suggests clearing it for site plans. Click Open. Revit builds the new model from the default IFC template and writes a log ending .ifc.log next to the IFC.

What to watch for

Fix far-off coordinates at the source. An IFC with large negative coordinates may not place geometry where you expect, whether you open it or link it. Autodesk recommends adjusting the origin or coordinate system in the authoring application before export (Autodesk Help: Open an IFC File, 2027).

Set the link's workset in both places. A link adds two elements: a type and an instance. If you move only the instance to a new workset, closing the type's workset makes the link disappear. Change the workset in the link's Properties and in its Type Properties (Autodesk Support: IFC link not displayed after closing Workset to which it was not assigned in Revit).

If link geometry looks wrong, check the link processor. Since Revit 2024.1, Link IFC uses a newer processor by default. Autodesk notes that some users see different performance or results. The LinkProcessor setting in the [ImportIFC] section of Revit.ini switches back to Legacy (Autodesk Help: Import IFC Settings in Revit.ini).

Expect references to move on reload. Dimensions to an IFC apply to faces of its geometry, not to center lines or reference planes. When the IFC changes, check every dimension and alignment you made to it before you issue sheets (Autodesk Help: Using IFC Files).

Doing it once is easy; doing it the same way at every desk is the problem. The template, class mapping and positioning option decide where the model lands. They also set its elements' categories and phase. When each person picks their own, the same consultant model can arrive in different places with different categories. Save one mapping file with Save As, keep it with the firm's IFC template, and write the positioning option into the project's BIM plan. Then do a workset pass each time a link lands. Mira can move a category of elements onto the right workset in one step you approve.

Or, just ask Mira to do it.

Mira is an AI partner for Revit that automates the work you repeat and builds tools your team needs.

  • Type this in Mira

    Move all the furniture from Workset1 to the Interiors workset.

    Mira tells you how many elements it will move and waits for your OK, then lists any it couldn't move, such as elements a teammate has borrowed.

Riverside_Medical_Center_ARCH.rvt — Level 02
FileArchitectureStructureAnnotateAnalyzeViewManagePirros
Level 02 ×A-501 Details3D View
Furniture on Workset1Result
Desk 60" x 30" (24)moved
Task Chair (44)moved
Task Chair (4)borrowed, left
Lounge Chair (12)moved
Conference Table (6)moved
Credenza (18)moved
Bookcase (20)moved
Side Table (10)moved
134 elements moved, 4 borrowed
Mira by PirrosLevel 02
Pirros
ChatSkillsHistory
Move all the furniture from Workset1 to the Interiors workset.
Reasoning
Thought for 3s
Query(Furniture on Workset1)
138 elements
Preview(138 to Interiors)
Approved
SetParameters(Workset x 138)
134 moved, 4 borrowed
Moved to Interiors134 of 138
Workset
Workset1 to Interiors
Moved, read back
134
Borrowed, left
4 task chairs
Undo
one step
Built into Mira
/bulk-set-parameters
In the / menu for everyone
Message Mira
Mira can make mistakes. Verify before you commit.
FAQ

Frequently asked questions.

Can't find what you're looking for?
Get in touch.

No. A linked IFC is read-only in the host model, though you can dimension to it, snap and align to it, and tag its elements. To change the geometry, ask the author for an updated IFC and reload the link. Opening the IFC as a new model is the other route, which Autodesk says isn't fully supported.

It's the intermediate Revit model that Revit builds from the IFC when you link it. Revit also writes a log file and a shared parameters file beside it, then links the intermediate model into yours. Don't edit it, or later reloads may stop picking up changes.

The Revit 2027 Help lists IFC2x3, IFC4 and IFC4.3 for linking. The Revit 2025 and 2026 Help lists IFC2x3, IFC2x2 and IFC2x for opening or linking, and IFC4 for linking only. When you open an IFC, Revit accepts ifc, ifcXML and ifcZIP files.

Check the positioning option first, then the file's coordinates. Origin-based placement puts the IFC's origin at Revit's internal origin, which can be far from the building. Files with large negative coordinates may also land out of position, so ask the author to adjust the origin before exporting.

Reload it from Manage Links, or close and reopen the project. Revit compares the IFC's timestamp and size, matches elements by IFC GUID, and adds, updates or deletes elements to match. Then recheck any dimensions or alignments you made to the link.

A link has a type and an instance, and each one sits on a workset. If only the instance was moved, closing the type's workset hides the link. Set the same workset in the link's Properties and its Type Properties.

Two ways in

Try it yourself.
Or bring it to the firm.

The download is free and takes a minute. The firm conversation is where your standards, your library, and your rollout get built. Start wherever makes sense.

Talk to us about your firm